We recommend to set Stabi/Function to Coaxial mode for Geo-fence, Return to Home and Position Hold features. 3.1.2 Dedicated GeoLink channel. Alternatively you can assign a GeoLink feature to any free channel in the General/Channels window. In the right part of the Spirit Settings software select which feature you would like to assign. FENCE INSTALLATION Fence panels should be installed starting from a gate post, free end or corner. If you are working on sloped ground and intend to step or slope the fence see the sections on the following page for the correct installation procedure. ASSEMBLE THE FRAMEWORK Lay the posts down on the ground and insert the top and bottom track. Attach to a fence. The boundary wire can only be attached to a wooden or chain link fence. When laying a double loop, ensure the wires are at least 5 feet apart. Use fence staples to attach the boundary wire to the fence. Avoid driving the staple in all the.

Free Spirit In Ground Fence Installation Instructions Free
In Ground Dog Fence Installation
Free Spirit In Ground Fence Installation Instructions Online
In Ground Fence System

čeština • ‎Deutsch • ‎English • ‎español • ‎français • ‎magyar • ‎italiano • ‎русский

2Compass Calibration
3How to configure
- 3.1Triggering
4Geo-fence
5Altitude Limit
- 5.1Usage
6Return to Home
- 6.2Modes
7Auto Landing
8Position Hold
9Altitude Hold
10Correction Gains

1 GeoLink Support

GeoLink is supported from firmware version 2.5. In order to utilize all the functions it is necessary to enable the support in the Spirit Settings - General tab first.After enabling, save the settings and re-power the model.

2 Compass Calibration

All GeoLink modules were fully tested and calibrated. The only thing pilot might need is to re-calibrate Compass.Compass is crucial for determining heading of the model for a proper navigation through space.Compass is sensing Earth's magnetic field (Geomagnetic field) and in this way it can determine heading at any time.Unfortunately Geomagnetic field is different everywhere. Thus if model will be operated outside the Czech Republic it is highly recommended to perform New Calibration. GeoLink modules are factory calibrated for the Czech Republic.

2.1 How to check

To verify that GeoLink is calibrated correctly for your area, please launch the Spirit Settings and open GeoLink settings window.At Info tab you can see current Heading value.

Please place the model or just GeoLink to the North as close as possible, so that flight direction of the model is front of the arrow.Ideally compare to an analogue compass.

When heading to North, you should see approximately 90 +/- 4°. Measured value should not be far from this. If so, please perform Compass Calibration again.

We recommend to not use a smart devices for compass heading comparison. These are usually not calibrated at all nor allow the calibration. An analogue compass is the best for comparison.

2.2 Odd behavior

If Compass calibration is wrong you will notice that features such as Geo-fence, Return to Home, Position Hold are not working precisely.For example when Return to Home is engaged and model reached programmed Home position, the model could move in a circle manner around that spot, instead of stable hovering.The bigger is circle, the bigger is Compass heading error. If you can observe this behavior always, then it is clear sign that you need to re-calibrate the Compass.

2.3 Calibration process

In order to perform the calibration it is necessary to enter Spirit Settings/GeoLink/Module and click the Calibration request button.Now you can disconnect power and USB interface cable from the model.

During following power up of the model you will immediately notice 3 series of rapid LED flashing on the GeoLink. This always signalize module is in the Calibration mode.
The Status LED will be indicating progress of the calibration then. Start moving with the model in all possible directions and angles to mimic a sphere. Any LED flash will indicate that a new calibration data were acquired.
Rotate with the module as long until you will see periodic LED flashing. At this point the calibration is finished. After following re-power the module is ready for operation.

For 600+ class helicopters we recommend to perform calibration while GeoLink is not mounted. In that way it can be more comfortable and easier.
Calibration should be done ideally at the flying field but can be performed usually indoor as well.

Spirit Setings will not see GeoLink during Calibration mode. Calibration will not finish until it is fully done. If power is turned off while calibration is not finished, the calibration process will start from the beginning after next power up.

3 How to configure

As the first step pilot has to decide what GeoLink feature he want to use. To find how each feature is working please visit Features page.Pilot can enable multiple features at the same time if needed.

Check feature you would like to use in the Aid tab of the GeoLink window.After enabling, available parameters for the particular feature will be accessible. By these parameters behavior of selected feature can be customized to fulfill a needs.For the first tries we recommend to use a default values.

3.1 Triggering

You can verify if triggering mechanism is working correctly even before actual flight by checking the Aid tab.If a feature is engaged you will see ACTIVE or in other case Inactive.

For safety reasons do not engage any GeoLink feature before model is in the air at appropriate altitude.

3.1.1 Stabi function

By default all GeoLink features are engaged as soon as a Stabi function is active. For example if Coaxial or Rescue mode is engaged the GeoLink feature is engaged as well and complement operation of a Stabi function by acting simultaneously.We recommend to set Stabi/Function to Coaxial mode for Geo-fence, Return to Home and Position Hold features.

3.1.2 Dedicated GeoLink channel

Alternatively you can assign a GeoLink feature to any free channel in the General/Channels window. In the right part of the Spirit Settings software select which feature you would like to assign. (for example F: Return to Home). Then select appropriate channel which will be used for engaging.You can use same channel for multiple features at the same time.

4 Geo-fence

To enable this feature it is required to tick the CheckBox in the GeoLink window/Aid tab.

4.1 Usage

The feature can be engaged at any given time by a command from your radio. It is important to decide in which way the feature can be engaged as there are two options.

To engage with Stabi function - in this case the feature is engaged when programmed Stabi function is engaged. This mean you do not need to assign any other switch than when used for e.g. Stabilisation mode
To engage with assigned GeoLink channel - it is required to assign F: GeoLink Geo-fence function in the General/Channels to an available channel.

Please make sure that Geo-fence Area was defined. Four points must be programmed. The Spirit Settings will display right order to program all points.

4.2 Modes

If Geo-fence is engaged by assigned GeoLink channel there is possibility to use tri-state switch also for programming of a new Geo-fence area.In the Channels window you will be able to see Function as On (1), Off and On (2) which is corresponding to 100%, 0% and -100% channel value.

When On (1) is displayed it mean that at this point Geo-fence is engaged and flight area is restricted. The model will return upon e

Free Spirit In Ground Fence Installation Instructions